LED Definitions

Port LED Definition for UfiSpace S9500-22XST

The network port LEDs are used to show the status of the link associated with the LED. In a UfiSpace S9500-22XST switch, there are 12*10G SFP+ ports, 8*25G SFP28 ports, and 2*100G QSFP28 ports on the front panel. The SFP, SFP28, and QSFP28 ports operate in a full duplex mode when the speed is 10Gbps, 25Gbps, or 100Gbps.

LED Condition Status

SFP+ Port LED

On (Green)

Link is up

Off

No link

SFP28 Port LED

On (Green)

Link is up

Off

No link

QSFP28 Port LED

On (Green)

Link is up

Off

No link

System LED Definition for UfiSpace S9500-22XST

The system LEDs are used to indicate the status of power and system.

LED Indicators Condition Status

Power

Off

No power or in shut down mode.

Solid Green

System power is good and the BMC heating is complete.

Blinking Green

System power is good and the BMC heating is in progress.

Solid Yellow

System power is good but BMC heating is failed.

Blinking Yellow

System power failure.

STAT (System Status)

Off

System (X86 and BMC) is no booted.

Solid Green

System boot is complete.

Blinking Green

System boot is in progress.

Solid Yellow

Reserved

Blinking Yellow

Reserved

PSU LED Functions and State

Off

No DC power to any of the PSUs.

Flashing Red

No DC power to this particular PSU.

Flashing Green

DC is present, only standby output is on. Poor contact.

Green

PSU DC output is on and is normal.

Red

PSU failure.

Flashing between Green and Red

Warning. Working condition is not satisfied. Check the voltage, electric current, and temperature.

FAN LED Functions and State

Off

Main board 3.3V power is failed or fan is not present.

Solid Green

Fan is present and interrupt de-assert.

Blinking Green

NA

Solid Yellow

NA

Blinking Yellow

Fan is present but interrupt assert.

Port LED Definition for UfiSpace S9600-32X

The network port LEDs are used to show the status of the link associated with the LED. In a UfiSpace S9600-32X switch, there are 4*10G SFP+ ports and 32*100G QSFP28 ports on the front panel. The SFP+ and QSFP28 ports operate in full duplex mode when the speed is 10Gbps and 100Gbps respectively.

LED Condition Status

SFP+ Port LED

On (Green)

Link is up

Off

No link

QSFP28 Port LED

On (Green)

Link is up

Off

No link

System LED Definition for UfiSpace S9600-32X

The system LEDs are used to indicate the status of power and system.

LED Condition Status

SYS

Off

System (x86 and BMC) is not booted.

Solid Green

System boot is complete.

Blinking Green

System boot is in progress.

Fast Blinking Green

Reserved.

Solid Amber

Power is up but system boot is failed.

Blinking Amber

Reserved

Fast Blinking Amber

Reserved

FAN

Off

Main board 3.3V_FAN power failure or no power.

Solid Green

All fans are working normally and interrupt de-assert.

Blinking Green

Fans PWMs do not match or each one fan no present

Fast Blinking Green

Reserved.

Solid Amber

Each one of fans is failure (PWM=0)

Blinking Amber

Fan is present but interrupt assert.

Fast Blinking Amber

Reserved

PSU1

Off

No DC power or standby is failed.

Solid Green

PSU DC output is ON and standby is normal.

Blinking Green

No PSU is present.

Fast Blinking Green

Reserved.

Solid Amber

PSU DC output is failed and standby is normal.

Blinking Amber

Warning. Working condition is not satisfied. (Check the voltage, electric current, and temperature).

Fast Blinking Amber

Reserved

PSU2

Off

No DC power or standby is failed.

Solid Green

PSU DC output is ON and standby is normal.

Blinking Green

No PSU is present.

Fast Blinking Green

Reserved.

Solid Amber

PSU DC output is failed and standby is normal.

Blinking Amber

Warning. Working condition is not satisfied. (Check the voltage, electric current, and temperature).

Fast Blinking Amber

Reserved

ID

Off

Turned off location of function

Solid Blue

Ready for location of function

Blinking Blue

Location of switch in telcom center

Fast Blinking Blue

Reserved.

Port LED Definition for UfiSpace S9600-72XC

The network port LEDs are used to show the status of the link associated with the LED. In an UfiSpace S9600-72XC switch, there are 64*25G SFP28 ports and 8*100G QSFP28 on the front panel. SFP28 and QSFP28 operate in full duplex mode when the speed is 25Gbps and 100Gbps respectively.

LED Condition Status

SFP28 Port LED

On (Green)

Link is up

Off

No link

QSFP28 Port LED

On (Green)

Link is up

Off

No link

System LED Definition for UfiSpace S9600-72XC

The system LEDs are used to indicate the status of power and system.

LED Condition Status

SYS

Off

No power

Solid Green

Host CPU/BMC boot is complete

Solid Amber

Power is up, but host CPU/BMC boot is failed.

FAN

Off

Fans are not initialized.

Solid Green

All fans are working normally.

Blinking Amber

Fan is not working. One or more fans need service.

PSU1

Off

No power

Solid Green

PSU1 is working normally.

Blinking Amber

PSU1 is failed. Service required.

PSU2

Off

No power

Solid Green

PSU2 is working normally.

Blinking Amber

PSU2 is failed. Service is needed.

Port LED Definition for UfiSpace S9510-28DC

The network port LEDs are used to represent the status of the link associated with the LED.

Port type Condition Status

SFP+

Up

Green

Down

Off

SFP28

Up

Green

Down

Off

QSFP28

Up

Green

Down

Off

System LED Definition for UfiSpace S9510-28DC

The system LEDs are used to indicate the status of power and system.

LED Indicators Behavior Status

Power

Off

No power or in shut down mode.

Solid Green

System power is good.

Blinking Green

System power is good but BMC power is failed.

Solid Yellow

System power is good but CPU power is failed.

Blinking Yellow

System power failure.

STAT (System Status)

Off

System (X86 and BMC) is not booted.

Solid Green

System boot is complete.

Blinking Green

System boot is in progress.

Solid Yellow

System boot is complete. (DIAG OS)

Blinking Yellow

Reserved

PSU LED Functions and State

Off

No DC power to any of the PSUs.

Flashing Red

No DC power to this particular PSU.

Flashing Green

DC is present, only standby output is on. Poor contact.

Green

PSU output is on and normal.

Red

PSU failure.

Flashing between Green and Red

Warning. Working condition is not satisfied. Check the voltage, electric current, and temperature.

FAN LED Functions and State

Off

Main board 3.3V power is failed or fan is not present.

Solid Green

Fan is present but interrupt assert

Blinking Green

NA

Solid Yellow

NA

Blinking Yellow

Fan is present but interrupt assert.

Port LED Definition for EdgeCore AGR130

The network port LEDs are used to represent the status of the link associated with the LED. In an Accton/EdgeCore AGR130 switch, there are 48*10G SFP+ ports and 6*100G QSFP28 on the front panel, the all SFP/QSFP28 will operate in full duplex mode when the speed is 10Gbps or 100Gbps.

LED Condition Status

SFP+ Port LED

On/Flashing Green

Link at 10G, flashing indicates activity

On/Flashing Amber

Link at 1G, flashing indicates activity

Off

No link

QSFP28 Port LED in 100G Mode (Port 49 - 54)

On/Flashing Green

Link at 100G, flashing indicates activity

Off

No link

QSFP28 Port LED in 25G Breakout Mode

On/Flashing Amber

Link at 25G in breakout mode, flashing indicates activity

Off

No link

QSFP28 Port LED in 40G Mode (Port 49 - 54)

On/Flashing Blue

Link at 40G mode, flashing indicates activity

Off

No link

QSFP28 Port LED in 10G Breakout Mode

On/Flashing Purple

Link at 10G in breakout mode, flashing indicates activity

Off

No link

System LED Definition for Edgecore AGR130

The system LEDs are used to indicate the status of power and system.

LED Condition Status

PSU1 (Power Supply Status)

Green

Power is operating normally

Amber

Power supply is present but not powered on or faulty.

Off

Power supply is not present.

PSU2 (Power Supply Status)

Green

Power is operating normally

Amber

Power supply is present but not powered on or faulty.

Off

Power supply is not present.

Diag (Diagnostic)

Green

System self-diagnostic test is successfully completed.

Amber

System self-diagnostic test detected a fault.

FAN

Green

System FAN is operating normally

Amber

Fan tray is present buy system FAN is faulty.

Off

System is off

Port LED Definition for EdgeCore AGR420

The network port LEDs are used to represent the status of the link associated with the LED.

Port type Condition Status

SFP+

Up

Blue LED is on (2 LEDs per port)

Down

Off

SFP28

Up

Blue LED is on (2 LEDs per port)

Down

Off

QSFP28

Up

Blue LED is on (2 LEDs per port)

Down

Off

System LED Definition for Edgecore AGR420

The system LEDs are used to indicate the status of power and system.

LED Condition Status

DIAG (Diagnostic)

Green

System self diagnostic test is successfully completed.

Amber

System self-diagnostic test has detected a fault. (Faulty Fan, thermal, or any interface.)

LOC

Flashing Amber

Flashing by remote management command. Assists technician in finding the right device for service in the rack.

Off

Not the switch that technician needs to find.

FAN

Green

System fan is working normally.

Amber

Fan tray is present but system fan is faulty.

Off

System is off.

PSU0 (power supply status)

Green

The power supply, #0, is working normally.

Amber

Power is present, but not ON. Power is faulty.

Off

Power supply is not present.

PSU1 (power supply status)

Green

The power supply, #1, is working normally.

Amber

Power is present, but not ON. Power is faulty.

Off

Power supply is not present.

Port LED Definition for Edgecore AGR400

The network port LEDs are used to represent the status of the link associated with the LED.

Port type Condition Status

SFP28

Up

Blue LED is on (Single LED per port)

Down

LED is Off

QSFP28

Up

Blue LED is on (2 LEDs per port)

Down

LED is Off

QSFP-DD

Up

Not tested

Down

Not tested

System LED Definition for Edgecore AGR400

The system LEDs are used to indicate the status of power and system.

LED Condition Status

DIAG (Diagnostic)

Green

System self diagnostic test is successfully completed.

Amber

System self-diagnostic test has detected a fault. (Faulty Fan, thermal, or any interface.)

LOC

Flashing Amber

Flashing by remote management command. Assists the technician in finding the right device for service in the rack.

Off

Not the switch that the technician needs to find.

FAN

Green

System fan is working normally.

Amber

Fan tray is present but system fan is faulty.

Off

System is off.

PSU0 (power supply status)

Green

The power supply, #0, is working normally.

Amber

Power is present, but not ON. Power is faulty.

Off

Power supply is not present.

PSU1 (power supply status)

Green

The power supply, #1, is working normally.

Amber

Power is present, but not ON. Power is faulty.

Off

Power supply is not present.

Port LED Definition for Edgecore CSR320

The network port LEDs are used to represent the status of the link associated with the LED.

Port type Condition Status

SFP+

Up

Green LED is on

Down

LED is Off

SFP28

Up

Green LED is on

Down

LED is Off

QSFP28

Up

Green LED is on

Down

LED is off

System LED Definition for Edgecore CSR320

The system LEDs are used to indicate the status of power and system.

Port type Condition Status

PSU0 (power supply status)

Green

The power supply, #0, is working normally.

Amber

Power is present, but not ON. Power supply is faulty.

Off

Power supply is not present.

PSU1 (power supply status)

Green

The power supply, #1, is working normally.

Amber

Power is present, but not ON. Power supply is faulty.

Off

Power supply is not present.

DIAG (Diagnostic)

Green

System self diagnostic test is successfully completed.

Blinking Green

System self-diagnostic test is in progress

Amber

System self-diagnostic test has detected a fault.

FAN

Green

System fan is working normally.

Blinking Green

System FAN tray is powered off when ambient temperature is less than 10 degree C.

Amber

Fan tray is present but faulty.

LOC

Flashing Amber

Flashing by remote management command. Assists the technician in finding the right device for service in the rack.

Off

Not the switch that the technician needs to find.

Port LED Definition for Delta AGCVA48S

The network port LEDs are used to show the status of the link associated with the LED. In the Delta’s AGCVA48S switch, there are 4*10G SFP+ ports and 48*25G SFP28 ports, and 10*100G QSFP28 ports on the front panel. The SFP+, SFP28, and QSFP28 ports operate in full duplex mode even when the speed is 10Gbps, 25Gbps and 100Gbps respectively.

Port type Condition Status

SFP+ Port LED

On (Green)

Link is up

Off

No link

SFP28 Port LED

On (Green)

Link is up

Off

No link

QSFP28 Port LED

On (Green)

Link is up

Off

No link

Port LED Definition for Edgecore CSR440

The network port LEDs are used to represent the status of the link associated with the LED.

Port type Condition Status

10G

Up

Green

Down

LED is Off

25G

Up

Blue

Down

LED is Off

100G

Up

Two LEDs per port. Green (on QSFP28) and Violet (on QSFP-DD).

Down

LED is off

System LED Definition for Edgecore CSR440

The system LEDs are used to indicate the status of power and system.

Port type Condition Status

PSU1 (power supply unit)

Solid Green

PSU1 is operating normally.

Solid Amber

Input power is present, but the PSU1 is not ON or is in a faulty state.

Off

The input power is not present or PSU1 is not present.

PSU2 (power supply unit)

Solid Green

PSU2 is operating normally.

Solid Amber

Input power is present, but the PSU2 is not ON or is in a faulty state.

Off

Input power is not present or PSU2 is not present.

DIAG (Diagnostic)

Solid Green

System self diagnostic test is successfully completed.

Blinking Green

System self-diagnostic test is in progress.

Solid Orange

System self-diagnostic test has detected a fault.

FAN

Solid Green

All fan modules are present and working normally.

Solid Orange

Fan module is present but a fault has been detected.

Off

Fan module is not present.

LOC

Blinking Blue

Flashing by remote management command. It helps technicians in finding the right device for service in the rack. It provides an indication of the location of the device.

Off

No indication.

ALARM

Solid Green

No alarms detected.

Solid Red

Local alarm is detected.